View TG322420GNCWCT1_6960511.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

confidential document page: 1 /23 data image corporation lcd module specification item no.: tg322420gncwc-t1 table of contents 1. cover & contents ??????????????????????????????????????????????? 1 2. record of revision ????????????????????????????????????????????? 2 3. general specifications ?????????????????????????????????????? 3 4. absolute maximum ratings ??????????????????????????????? 4 5. electrical characteristics ?????????????????????????????? 5 6. electro-optical characteristic ?????????????????????? 5 7. timing characteristics ????????????????????????????????????? 8 8. pin connections ?????????????????????????????????????????????????? 12 9. power supply ??????????????????????????????????????????????????????? 12 10. block diagram ???????????????????????????????????????????????????? 13 11. touch panel characteristics ??????????????????????????? 14 12. quality assurance ????????????????????????????????????????????? 16 13. lot numbering system ??????????????????????????????????????? 20 14. lcm numbering system ??????????????????????????????????????? 20 15. precautions in use lcm ??????????????????????????????????????? 21 16 outline drawing ?????????????????????????????????????????????????? 22 17. package information ????????????????????????????????????????? 23 r&d dept. q.c. dept. eng. dept. prod. dept. version: issued date: sheet code: total pages: b 2003/5/14 23
confidential document page: 2 /23 2. record of revision rev date item page comment b may/14/03 3,4,5,7. 1,8,9, 10.1, 12.1.5 3-6,9-13,16 1.modtify storage temperature from-20 ~ 70 c to ?20~60 c. 2.modtify operating temperature from 0 ~ 50 c to 0~45 c. 3.modtify electrical absolute maximum ratings. 4.modtify electrical characteristics. 5.modtify timing chart. 6.modtify pin connection symbols. 7.modtify block diagram. 8.add display pattern 9.modtify t est method storage temperature from -20 ~ 70 c to ?20~60 c, operating temperature from 0 ~ 50 c to 0~45 c. 10.modtify environmental absolute maximum ratings. 11.modtify power supply.
confidential document page: 3 /23 3. general specification display format : 320 (w) 240 (h) dots dots pitch : 0.36 (w) 0.36 (h) mm dots size : 0.34 (w) 0.34 (h) mm view area : 121 (w) 91.6 (h) mm general dimensions : 166 (w) 109 (h) 9.2 (t) mm max. weight : g max. v lcd type : stn stn yellow fstn polarizer mode : reflective transflective v transmissive negative v view angle : 6 o?clock 12 o?clock others v backlight : led el ccfl backlight color : yellow green amber blue green v white others controller / driver : nt7701 / nt7705 v normal wide temperature operating 0 to 45 c operating -20 to 70 c temperature range : storage -20 to 60 c storage -30 to 80 c
confidential document page: 4 /23 4. absolute maximum ratings 4.1 electrical absolu te maximum ratings v ss = 0v, ta = 25 c item symbol min. max. unit supply voltage (logic) v dd -v ss -0.3 6.5 v supply voltage (lcd driver) v ee -v ss -0.3 30 v input voltage v i v ss v dd v operating temperature t op 0 45 c storage temperature t stg -20 60 c 4.2 environmental absol ute maximum ratings operating storage item (min.) max.) (min.) (max.) comment ambient temp 0 45 -20 60 note (1) humidity note (2) note(2) without condensation vibration -- 4.9m/s 2 -- 19.6m/s 2 xyz direction shock -- 29.4m/s 2 -- 490m/s 2 xyz direction note(1) ta = 0 c : 50hr max. note(2) ta 40 c : 90% rh max. ta 40 c : absolute humidity must be lower than the humidity of 90% rh at 40 c .
confidential document page: 5 /23 5. electrical characteristics item symbol condition min. typ. max. unit supply voltage (logic) v dd -v ss 2.5 5 5.5 v 0 c 21.7 22.4 23.1 25 c 20.8 21.5 22.2 supply voltage (lcd) v ee -v ss 50 c 20.0 20.7 21.4 v v ih 0.8*vdd -- v dd input voltage v il -- vss -- 0.2*vdd v i dd -- 0.5 -- logic supply current i ee 25 c v dd -v ss=5v -- 4.0 -- ma 6. electro-optica l characteristics item symbol condition min. typ. max. unit ref. 0 c -- -- -- rise time tr 25 c 200 450 ms 0 c -- -- -- fall time tf 25 c 300 700 ms note (1) contrast k 25 c 3 4 note (3) -- 25 -- view angle 1 ~ 2 ? 1, ? 2 25 c & cr 2 -- 20 -- note (2) frame frequency ff 25 c 32 64 128 hz note (1) & (2) : see next page note (3) : contrast ratio is defined under the following condition: cr= brightness of non-selected condition brightness of selected condition ( a ). temperature ---------- 25 c ( b ). frame frequency ---- 64hz ( c ). viewing angle -------- = 0 , ? = 0 ( d ). operating voltage --- 21.5v
confidential document page: 6 /23 note (1) response time is measured as the shortest period of time possible between the change in state of an lcd segment as demonstrated below: wave form 90% brightness 100% 10% t r t f condition: ( a ) . temperature ---------------25 c ( b ) . frame frequency --------- 64hz ( c ) . view angle ----------------- = 0 , ? =0 ( d ) . operating voltage -------- 21.5v note (2) definition of view angle top ? bottom direction right -- left direction top ? 2 ? 1 1 2 bottom left right
confidential document page: 7 /23 6.1 ccfl electrical characteristic item condition start voltage 500 vrms min,at ta=25 c tube voltage 300vrms typ,at ta=25 c tube current 5m arms typ ,at ta=25 c drive frequency 30 khz , typ at ta=25 c life time min=15khrs typ=20 khrs 6.1.2 initial optical characteristics item condition brightness uniformity 75% min. 500 cd/m 2 min. average brightness 550 cd/m 2 typical x 0.322 0.015 chromaticity y 0.327 0.015 6.1.3 environme ntal conditions item temperature humidity unit operating -10 to 60 c 20 to 90% rh storage -20 to 70 c 5 to 90% rh recommend ccfl inverter: tdk l10l operation voltage +12v , 300ma tdk l10a operation voltage +5v , 600ma
confidential document page: 8 /23 7. timing characteristics segment timing: (vss=0v,vdd=4.5-5.5v,vo=15 to 30, and ta=-30 to 85 c, unless otherwise noted ) item symbol condition min. typ. max. units shift clock period t wck tr ,tf 10ns,note 1 71 ns shift clock ?h?/ ?l? pulse width t wckh ; t wckl 23 ns data setup time t ds 10 ns data hold time t dh 20 ns latch pulse ?h? pulse width t wlph 23 ns shift clock rise to latch pulse rise time t ld 0 ns shift clock fall to latch pulse fall time t sl 25 ns latch pulse rise to shift clock rise time t ls 25 ns latch pulse fall to shift clock fall time t lh 25 ns input signal rise/ fall time t r , t f note2 50 ns enable setup time t s 21 ns dispoff removal time t sd 100 ns dispoff enable pulse width t wdl 1.2 s output delay time (1) t d cl=15pf 40 ns output delay time (2) (3) t pd1 ,t pd2, t pd3 cl=15pf 1.2 s (vss=0v,vdd=2.5-4.5v,vo=15 to 30, and ta=-30 to 85 c, unless otherwise noted ) item symbol condition min. typ. max. units shift clock period t wck tr,tf 11ns,note 1 125 ns shift clock ?h?/ ?l? pulse width t wckh ; t wckl 51 ns data setup time t ds 30 ns data hold time t dh 40 ns latch pulse ?h? pulse width t wlph 51 ns shift clock rise to latch pulse rise time t ld 0 ns shift clock fall to latch pulse fall time t sl 51 ns latch pulse rise to shift clock rise time t ls 51 ns latch pulse fall to shift clock fall time t lh 51 ns input signal rise/ fall time t r , t f note2 50 ns enable setup time t s 36 ns dispoff removal time t sd 100 ns dispoff enable pulse width t wdl 1.2 s output delay time (1) t d cl=15pf 78 ns output delay time (2) (3) t pd1 ,t pd2, t pd3 cl=15pf 1.2 s note1: take the cascade connection into consideration. note2: ( tck-t wckh -t wckl )/2 is the maximum in the case of high speed operation.
confidential document page: 9 /23 segment timing t wlph cl1(lp) t sl tlh tld t ls t wckh t wckl cl2(xck) tr tf t wck t ds t dh d0~d3 last data top data t wdl t sd dispoff (/doff) cl1(lp) 1 2 n cl2(xck) t s ei t d eo n:4-bit parallel mode 40 8-bit parallel mode 20 fr t pd1 lp tpd 2 dispoff (/doff) t pd3 y1~y160
confidential document page: 10 /23 common timing: (vss=0v,vdd=2.5-5.5v,vo=15 to 30v, and ta=-30 to 85 c, unless otherwise noted ) item symbol condition min. typ. max. units shift clock period t wlp tr ,tf 20ns 250 ns vdd=+5.0v 10% 15 ns shift clock ?h? pulse width t wlph vdd=+2.5-+4.5v 30 ns data setup time t su 30 ns data hold time t h 50 ns input signal rise/ fall time t r , t f 50 ns dispoff removal time t sd 100 ns dispoff enable pulse width t wdl 1.2 s output delay time (1) t dl cl=15pf 200 ns common timing t wlp t wlph tf cl1(lp) t su t h tr eio2 t dl ei01 t sd dispoff (/doff) t wdl
confidential document page: 11 /23 7.1 timing chart s(flm) 240 1 2 240 1 2 240 1 2 cl1(lp) s(flm) cl1(lp) cl2(xck) xck x ( 320 / 4 ) pulse do-d3 7.2 power on/off timing vdd 0.8 vdd 0~50ms 0 ~50ms 0.8 vdd vdd vss vss signal vss 20ms min. 0ms vss vee vo vss vss power on the missing pixels may occur when the lcm is driven beyond above power interface timing sequence.
confidential document page: 12 /23 8. pin connections no symbol function 1 s(flm) first line mark for common scan 2 cl1(lp) data latch pulse 3 cl2(xck) data shift clock 4 n.c no connection 5 disp off(/doff) display on/ off control input (?h?=on, ?l?=off) 6 d0 7 d1 8 d2 9 d3 h/l display data 10 vdd power supply for logic 11 vss power supply (0v) 12 vee(vo) lcd contrast voltage(+) ccfl(cn2) no symbol function 1 hot ccfl hot + 2 nc -- 3 gnd ccfl gnd - 9. power supply lcm vee +19v~+24v pcb vdd +5v vss hot ccfl b/l gnd
confidential document page: 13 /23 10. block diagram s(flm) common driver 2 240 lcd panel 320 240 320 cl1(lp) segment driver x2 /doff cl2(xck) d3-d0 vdd vss vee(vo) lcd bias circuit 10.1 display pattern first data com001 d3 d2 d1 d0 d3 d2 d1 d0 com002 d3 d2 d1 d0 d3 d2 d1 d0 com239 d3 d2 d1 d0 d3 d2 d1 d0 com240 d3 d2 d1 d0 d3 d2 d1 d0 seg001 seg002 seg319 seg320 320*240 dots matrix fr ckt.
confidential document page: 14 /23 11. touch panel characteristics 1.scope this specification is applied to data image display devices product/ tg322420 2. features type : analog resistive type touch panel input mode : pen or finger structure: pet-------------non glare ito film, 175 m clear ito film, 175 m glass------------ito glass, 1.1mm tape gasket----60 m dot pitch-------1.0 mm(optional) connector : fpc 3. general specification item specification unit ito glass 1.1 0.1(t) mm fpc (ito film) 175 15(ito film) m connector fpc,4-pin connector (l50*w5.0),pitch=1.0 mm total thickness 137.4 0.3(w)*108.9 0.3(h)*1.5 0.15(t) mm 4. rating 4.1 the maximum voltage: dc 7volts 4.2 usable temperature range from: 0 c to 45 c(20~90%) 4.3 storage temperature range from: ?25 c to 60 c(20~90%) 5. electrical specification 5.1resistance between leads: film(x axis) glass (y axis):200~900 ? 5.2linearity : x axis 1.5% , y axis 1.5% 5.3insulation resistance: 20 m ? @dc 25v 5.4chattering time : 10msec @100k ? pull -up 6. mechanical specification 6.1input method pen or finger 6.2operating force: 80g with r8.0 hs40 silicon rubber 80g with r0.8 polyacetal pen 6.3surface hardness: 2h (pencil test) ,hard coated pet 6.4light transmission: 75% (non glare type),80% (clear type) (@550nm, spectro photometer hitachi u3300) 7.durability 7.1 durability against writing characters after writing 200,000 characters in the same area (20mm*20mm), force : 250g , speed: 1,000 characters/hour ? resistance between leads : film (x axis) glass (y axis) ? linearity : x axis 1.0% , y axis 1.0% ? insulation resistance: 20 m ? @dc 25v 7.2 punching life after punching 1,200,000 times with the r8.0 silicon rubber force : 250g, speed:2/sec ? resistance between leads : film (x axis) glass (y axis) ? linearity : x axis 1.0% , y axis 1.0% ? insulation resistance: 20 m ? @dc 25v
confidential document page: 15 /23 7.3 impact resistance: no damage when 9mm steel ball is dropped on the surface from 30cm height at 1 time. 7.4 flexible pattern heat seal peeling strength :1.5n/cm (peeling upward by 90deg. speed:50mm/min) 7.5 flexible pattern bending resistance bending: 3 times or more by bending radius r1.0mm. 7.6 flexible pattern insert/pull out resistance 5 times at least. the requirements in 5.1 shall be satisfied. 7.8 vibration resistance (in operation) no faulty operation when sweep vibration of 0.2g 10~55hz (1min.) is given for 30min. each in the directions of x,y,z. (not in operation ) the requirements in 6.2 and 5.1~5.4 shall be satisfied after sweep vibration of 2g 10~55hz (1min.) is given for 30min. each in the directions of x,y,z. 7.9 package drop no damage to the product.(1 corner edge, 2 ridges, 4 surfaces, drop from 50 cm height:65cm for the bottom) 8. reliability 8.1 high temperature test after putting panels at 80 c for 120 hours, then leaving for 24 hours at room temperature. ? resistance between leads : film (x axis) glass(y axis) ? linearity : x axis 1.5% , y axis 1.5% ? insulation resistance: 20 m ? @dc 25v ? operating fore : 80g with r8.0 hs40 silicon rubber 80g with r0.8 polyacetal pen 8.2 low temperature test ? after putting panels at-40 c for 120 hours, then leaving for 24 hours at room temperature. ? resistance between leads : film (x axis) glass(y axis) ? linearity : x axis 1.5% , y axis 1.5% ? insulation resistance: 20 m ? @dc 25v ? operating fore : 80g with r8.0 hs40 silicon rubber 80g with r0.8 polyacetal pen 8.3 temperature and humidity test: after putting panels at 60 c, 90%rh for 120 hours, then leaving for 24 hours at room temperature ? resistance between leads : film (x axis) glass(y axis) ? linearity : x axis 1.5% , y axis 1.5% ? insulation resistance: 20m ? @dc 25v ? operating fore: 80g with r8.0 hs40 silicon rubber 80g with r0.8 polyacetal pen 8.4 repetition of high and low temperature after putting panels at the condition of -40 c for 30minutes,and then 80 c for 30 minutes and this process is repeated by 10 cycles, then leaving for 24 hours at room temperature. ? resistance between leads : film (x axis) glass(y axis) ? linearity : x axis 1.5% , y axis 1.5% ? insulation resistance: 20 m ? @dc 25v ? operating fore : 80g with r8.0 hs40 silicon rubber 80g with r0.8 polyacetal pen
confidential document page: 16 /23 12. quality assurance 12.1 test condition 12.1.1 temperature and humidity(ambient temperature) temperature : 20 5 c humidity : 65 5% 12.1.2 operation unless specified otherwise, test will be conducted under function state. 12.1.3 container unless specified otherwise, vibrat ion test will be conducted to the product itself without putting it in a container. 12.1.4test frequency single cycle. 12.1.5test method no. parameter conditions regulations 1 high temperature operating 45 2 c note 3 2 low temperature operating 0 2 c note 3 3 high temperature storage 60 2 c note 3 4 low temperature storage -20 2 c note 3 5 vibration test (non-operation state) total fixed amplitude : 1.5mm vibration frequency : 10 ~ 55hz one cycle 60 seconds to 3 directions of x.y.z. for each 15 minutes note 3 6 damp proof test (non-operation state) 40 c 2 c, 90~95%rh, 96h note 1,2 7 shock test (non-operation state) to be measured after dropping from 60cm high once concrete surface in packing state note 3 note 1: returned under normal temperature and humidity for 4 hrs. note 2: no dew condensation to be observed. note 3: no change on display and in operation under the test condition
confidential document page: 17 /23 12.2 inspection condition 12.2.1 inspection conditions the lcd shall be inspected under 40w white fluorescent light. 45 12.2.2 definition of applicable zones b lcd a bezel pcb a : display area b : non-display area
confidential document page: 18 /23 12.2.3 inspection parameters no. parameter criteria 1 black or white spots acceptable number zone dimension a b class of defects aql level d < 0.15 ? ? 0.15 d< 0.2 4 4 0.2 d 0.25 2 2 d 0.3 0 1 minor 2.5 d = (long + short) / 2 * : disregard 2 scratch, substances acceptable number x (mm) zone y(mm) a b class of defects aql level ? 0.04 w ? ? 3.0 l 0.06 w 4 4 2.0 l 0.08 w 2 3 ? 0.1 < w 0 1 minor 2.5 x : length y : width ? : disregard total defects should not exceed 4/module 3 air bubbles (between glass & polarizer) acceptable number zone dimension a b class of defects aql level d 0.15 ? ? 0.15 < d 0.25 2 ? 0.25 < d 0 1 minor 2.5 ? : disregard total defects shall not excess 3/module. 4 uniformity of pixel (1) pixel shape (with dent) 0.152
confidential document page: 19 /23 4 uniformity of pixel (2) pixel shape ( with projection) should not be connected to next pixel 0.152 (3) pin hole x y ( x + y )/2 0.02mm (less than 0.1 mm is no counted) (4) deformation x ( x + y ) / 2 0.3mm y total acceptable number : 1/pixel, 5/cell definition major aql 0.65% it is a defect that is likely to result in failure or to reduce materially the usability of the product for the intended function. aql 1.00% it is a defect that is likely to assembly size and not result in functioning problem. class of defects minor aql 2.5% it is a defect that will not result in functioning problem with deviation classified. 12.3 sampling condition unless otherwise agree in written, the sampling inspection shall be applied to the incoming inspection of customer. lot size: quantity of shipment lot per model. sampling type: normal inspection, single sampling sampling table: mil-std-105e inspection level: level ii
confidential document page: 20 /23 13. lot numbering system 9 7 4 2 production week number production year 14. lcm numbering system tg 322420 g n c w c ? t1 version :t1 view direction & temp. range a?bottom view 6h & normal temp. b?bottom view 6h & wide temp. c?top view & normal temp. d?top view & wide temp. backlight color b ?blue w ?white n ?none backlight s ?edge light led b/l e ?el c ?ccfl b/l mode m ? transmissive r ? reflective f ? transflective n - negative lcd type g ? stn s ?stn yellow f ? fstn series code 3224 20 ?320 dots x 240 dot, 2 lcd type, 0 pcb type model type cm ? character module gm ? graphic module tg?slim tab/cog module tx?custom slim tab/cog module
confidential document page: 21 /23 15. precaution for using lcm 1. liquid crystal display (lcd) lcd is made up of glass, organic sealant, organic fluid, and polymer based polarizers. the following precautions should be taken when handing, (1). keep the temperature within range of use and storage. excessive temperature and humidity could cause polarization degredation, polarizer peel off or bubble. (2). do not contact the exposed polarizers with anything harder than an hb pencil lead. to clean dust off the display surface, wipe gently with cotton, chamois or other soft material soaked in petroleum benzin. (3). wipe off saliva or water drops immediately. contact with water over a long period of time may cause polarizer deformation or color fading, while an active lcd with water condensation on its surface will cause corrosion of ito electrodes. (4). glass can be easily chipped or cracked from rough handling, especially at corners and edges. (5). do not drive lcd with dc voltage. 2. liquid crystal display modules 2.1 mechanical considerations lcm are assembled and adjusted with a high degree of precision. avoid excessive shocks and do not make any alterations or modifications. the following should be noted. (1). do not tamper in any way with the tabs on the metal frame. (2). do not modify the pcb by drilling extra holes, changing its outline, moving its components or modifying its pattern. (3). do not touch the elastomer connector, especially insert an backlight panel (for example, el). (4). when mounting a lcm make sure that the pcb is not under any stress such as bending or twisting . elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the elements. (5). avoid pressing on the metal bezel, otherwise the elastomer connector could be deformed and lose contact, resulting in missing pixels. 2.2. static electricity lcm contains cmos lsi?s and the same precaution for such devices should apply, namely (1). the operator should be grounded whenever he/she comes into contact with the module. never touch any of the conductive parts such as the lsi pads, the copper leads on the pcb and the interface terminals with any parts of the human body. (2). the modules should be kept in antistatic bags or other containers resistant to static for storage. (3). only properly grounded soldering irons should be used. (4). if an electric screwdriver is used, it should be well grounded and shielded from commutator sparks. (5) the normal static prevention measures should be observed for work clothes and working benches; for the latter conductive (rubber) mat is recommended. (6). since dry air is inductive to static, a relative humidity of 50-60% is recommended. 2.3 soldering (1). solder only to the i/o terminals. (2). use only soldering irons with proper grounding and no leakage. (3). soldering temperature : 280 c 10 c (4). soldering time: 3 to 4 sec. (5). use eutectic solder with resin flux fill. (6). if flux is used, the lcd surface should be covered to avoid flux spatters. flux residue should be removed after wards. 2.4 operation (1). the viewing angle can be adjusted by varying the lcd driving voltage v0. (2). driving voltage should be kept within specified range; excess voltage shortens display life. (3). response time increases with decrease in temperature. (4). display may turn black or dark blue at temperatures above its operational range; this is (however not pressing on the viewing area) may cause the segments to appear ?fractured?. (5). mechanical disturbance during operation (such as p ressing on the viewing area) may cause the segments to appear ?fractured?. 2.5 storage if any fluid leaks out of a damaged glass cell, wash off any human part that comes into contact with soap and water. never swallow the fluid. the toxicity is extremely low but caution should be exercised at all the time. 2.6 limited warranty unless otherwise agreed between data image and customer, data image will replace or repair any of its lcd and lcm which is found to be defective electrically and visually when inspected in accordance with data image acceptance standards, for a period on one year from date of shipment. confirmation of such date shall be based on freight documents. the warranty liability of data image is limited to repair and/or replacement on the terms set forth above. data image will not responsible for any subsequent or consequential events.
confidential document page: 22 /23 16.outline drawing cn2 contact side 1. tu 2. tr 3. td 4. tl tl td tu tr ~ cn3 ~ ~ cn2 ~ 1.hot 2. nc 3. gnd ffc cable ccfl connector cn3 pin 1 3 1. unspecified tol to be 0.5 2. ccfl connector : bhr-03vs-1(jst) 3. ccfl cable : ul3579.awg26 4. ffc cable : pitch=1.25 [ note ] pin 1 320 x 240 dots detail of dots scale:10/1 5. touch panel connector : pitch=1.0 pin 1 pin 4 cn1 pin 12 pin 1 12. vee(vo) ~ cn1 ~ 4. n.c(m) 3. cl2(xck) 2. cl1(lp) 1. s(flm) interface cable 5. disp off 6. d0 9. d3 11. vss 10. vdd 8. d2 7. d1 contact side
confidential document page: 23 /23 17. package information module carton anti-static pet tray

▲Up To Search▲

Price & Availability of TG322420GNCWCT1

	To Download TG322420GNCWCT1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .